[ndnSIM] Fwd: ndnSIM didn't receive packet

[Anil Jangam]

Check whats different between the two topology config files and you will
know what caused the issue.
On May 28, 2016 11:31 AM, "qhsong" <ndn at sqh.me> wrote:

> Hi Anil,
> Finally I change the way ,all Nodes are put in topo.txt and then I let
> program read it. It works.
> But I still not find the problem.
> Thanks for your help.
>
> Best Regards,
> qhsong
>
> 2016-05-28 20:50 GMT+08:00 Anil Jangam <anilj.mailing at gmail.com>:
>
>> Check if your topology configuration file is setting any P2P link
>> properties, which might be causing delay or timeouts. Mask all link level
>> properties for now and retest.
>> On May 23, 2016 11:05 PM, "qhsong" <ndn at sqh.me> wrote:
>>
>> Hi Sabet,
>> I can sure FIBs seem no problem. Because I change node generator method,
>> it works.I did't use consume app, just use default ndn-producer and
>> ndn-consumer.
>>
>> Thanks,
>> qhsong
>>
>> 2016-05-24 13:35 GMT+08:00 Muhammad Hosain Abdollahi Sabet <
>> mhasabet at gmail.com>:
>>
>>> qhsong,
>>>
>>> I don't want to interrupt. But I had a similar problem recently.
>>> Interests reach a node, but OnInterest method is not being called, right?
>>> Are you using a cutom app? Are sure you have FIBs populated correctly?
>>>
>>> Thanks,
>>> Sabet
>>>
>>> خندان باشید
>>> با تشکر
>>>
>>> On Tue, May 24, 2016 at 9:50 AM, qhsong <ndn at sqh.me> wrote:
>>>
>>>>
>>>> Hi JunXiao,
>>>>
>>>> First I TopologyReader like this:
>>>>
>>>>     AnnotatedTopologyReader topologyReader("", 25);
>>>>     topologyReader.SetFileName("scratch/topo.txt");
>>>>     topologyReader.Read();
>>>>
>>>> Then ,create some Nodes by this:
>>>>    NodeContainer consumerNodes;
>>>>    consumerNodes.Create(3);
>>>>
>>>> I connected then with p2pHelper:
>>>>
>>>> for(int i=0;i<3;i++) {
>>>>       PointToPointHelper p2p;
>>>>       p2p.Install(Names::Find<Node>("Node_in_Topo.txt"),
>>>> consumerNodes.get(i));
>>>> }
>>>>
>>>> Install ndnHelper one by one.
>>>> for(int i=0;i<3;i++) {
>>>>     ndn::helper ndnHelper;
>>>>     //set content store size in different value
>>>>     ndnHepler.Install(consumerNodes);
>>>> }
>>>>
>>>> then Install ndnHelper in topo.txt node. Install consumer and producer
>>>> in other node.
>>>>
>>>> That's what I do for ndnSIM.
>>>> I also note that in --vis mode, the node I use NodeContainer.Create is
>>>> gray, and other nodes is red.
>>>>
>>>> Is this wrong?After I switch all node generator by topo.txt, It works.
>>>>
>>>> Thanks,
>>>> qhsong
>>>>
>>>>
>>>> 2016-05-24 11:39 GMT+08:00 Junxiao Shi <shijunxiao at email.arizona.edu>:
>>>>
>>>>> Hi qhsong
>>>>>
>>>>> Can you post a code snippet that shows what you are doing, and
>>>>> indicate what does not work?
>>>>>
>>>>> Yours, Junxiao
>>>>>
>>>>> On Mon, May 23, 2016 at 8:36 PM, qhsong <ndn at sqh.me> wrote:
>>>>>
>>>>>> Hi,
>>>>>> Thanks for your help.  I first use AnnotatedTopologyReader and then
>>>>>> use NodeContainer.Create() some node, I try to use p2p connection to
>>>>>> connection them ,then use ndnHelper.Install().
>>>>>> Then I change all node generator by AnnotatedTopologyReader, It works.
>>>>>> Maybe AnnotatedTopologyReader not compatible with NodeContainer.
>>>>>> Is this a bug?
>>>>>>
>>>>>> Thanks for your help.
>>>>>> qhsong
>>>>>>
>>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> ndnSIM mailing list
>>>> ndnSIM at lists.cs.ucla.edu
>>>> http://www.lists.cs.ucla.edu/mailman/listinfo/ndnsim
>>>>
>>>>
>>>
>>
>> _______________________________________________
>> ndnSIM mailing list
>> ndnSIM at lists.cs.ucla.edu
>> http://www.lists.cs.ucla.edu/mailman/listinfo/ndnsim
>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.lists.cs.ucla.edu/pipermail/ndnsim/attachments/20160528/6d9e0e3c/attachment.html>